The sail looks really great.

I think those semi-circular wrinkles show that the sail is set up just right and I'm not surprised that a sail like that, on a hull like that, should cause a few jaws to drop.

Hi,

three weeks into cruising with the new junk rig on my Ilvy, and I can't even imagine to sail bermudan again. We pretty quickly got used to the altered handling, as it is pretty simple. The longest it probably took to find handy german words for YHP and THP, which would slip fluently enough through ones lips to shout them even in a gale. We stayed with "Kopf" (YHP) and "Hals" (THP) - quite uncreative I guess.

Tacking is fantastic. We quickly adapted to grab ones coffee cups as soon as the "ready to tack!?" is heared, and just slip to the other side of the cockpit without sacrifying one drop of that black gold.

Only few things I changed after installation and departure from Kiel:

• Before, I tried to recycle the main sheet running block for the junk rig. However, it is obviously not made for 8mm line, and the sheet often slipped in a strong gust - annoying and hurts the sheet. Replaced it with two old standard blocks from the old rig, and lead it to the portside winch (I think similar to what I saw on Arne's Ingeborg). Looks a bit cramped now, but works just fine.
• I still had two easyblock thingies laying around. Installed it in Klintholm, for FUP, YHP and THP. Works like a charme, really quick and safe, compared to my old system of using standard cleats.
• The mast is now waxed (standard candle) just where the sailbundle rests. That totaly silenced the annoying squeeking of the bundle at anchor due to swell.
• Installed telltales near the luff. However, I could not quite look through the fabric, so it was a bit useless and I teared them off again.
  

Some (minor) open issues remain:

• Setting, Lowering and Reefing in choppy seas: the whole sail flies around like crazy in a frantic forward-aftward motion along the mast, as soon as the sheet is let go and YHP and THP are loosened. Still need to find a sweet way to to this.
• As I did not build such a sail bundle holder as described in PJR, the bundle swings left and right quite a lot in choppy seas, even if sheeted in strongly. I guess I should have listened to the PJR...
• Oh, and I am thinking about printing a fact sheet/ FAQ for the junk rig, laminating it waterproof, and hanging it on the railing or pulpit. Always the same questions in harbors... some develop into really interesting discussions, some I could happily omit.

All in all, one of my best sailing experiences so far.

Cheers,

Paul

Paul,

I’ve received a few remarks about that ‘untidy’ gap between the forward and aft batten pocket. It is the way it is, and is not a result of any stress, so I just disregard it, and suggest you do the same. The actual batten panels on your photo set better now with more camber in them.
Maybe I should write a few words about it in Chapter 7 of TCPJR, if I bother...

I am looking forward to reading more reports from your Sweden cruise. Sweden it THE Maxi 77 country, so you will no doubt receive a lot of comments.

Cheers,
Arne

Paul S’ shown GPS track from his Maxi 77 looks very good. However, it is hardly surprising  -  after all, that sail is a straight 1:1 copy of the blue sail of Boudicca, last month’s BOTM. Boudicca sails well, and her four lower panels actually happen to be 1:1 copies of those in my Ingeborg’s sail.

That 35.4sqm sail area on the smaller Maxi, brings the SA/disp. up to almost 22.

Paul; in your photo I notice a horizontal crease along each of the four lower battens. In case they have not disappeared by themselves, I suggest you ease the tension in the sail with 20-40mm along these battens.

Cheers,
Arne

A little more than one grand